Toyota Ifs Steering Box Mount

I used some emu springs off the rear of my 94 truck for my SAS which have the center pin way up front so my steering box had to crowd into the drivers front body mounts space to avoid smacking the tie rod on. 5 Remove Sector Shaft.

Ifs Steering Box Mount Kit

IFS Steering Box Mount If youre installing crossover steering on your 79-85 4wd Toyota youre going to need to mount an IFS steering box.

Toyota ifs steering box mount. Toyota IFS Steering Box Mount Kit. Inner plate is 316 outer plate is 14. 3 Remove the pitman arm.

IFS Steering Box Mount Kit. This frame mount kit includes both inner and outer frame reinforcing plates grade 8 bolts DOM tubing and Crimp nuts. Add to Wish List.

Items 1-33 of 50. Unbolt or cut off with a torch the factory push-pull steering box mount. Can also be used on anything utilizing a Toyota IFS box such as Classic Broncos.

Chevy Dana 44 Steering. Toyota Heavy Duty Steering Box Mount Kit. You need to adapt the high steer kit to your IFS box pitman arm.

Plates are 14 and 316 material Dom sleeves are 34 OD 120 wall USA tube. This frame mount kit includes both inner and outer frame reinforcing plates grade 8 bolts DOM tubing and Crimp nuts. This is a standard swap item on early Toys.

Clamps see that are drilled out the length of the advice guys at this warranty replacement toyota ifs boxes. View as Grid List. Add to Wish List.

The Issue with Attaching High Steer. DOM Sleeves for inserting through frame. 1 Center the pitman arm.

Remove stock steering box steering arms front axle anti wrap bar. Leaf Spring Frame Tubes for IFS to Leaf Spring Conversion. Coast gear mounting area where to keep the arms are drilled the gear and bearings.

IFS Steering Box Mount If youre installing crossover steering on your 79-85 4wd Toyota youre going to need to mount an IFS steering box. Obtain an IFS steering box from a 1986-1995 4wheel drive Pickup or 4Runner note 2wd steering box will not work. Align it to match the steering column path I built a prototype bracket that would need to be welded to the frame but would also need to build an extension for the column and reverse the pitman arm so it faces forward ifs have reverse movement.

This frame mount kit includes everything you need to mount a Toyota IFS Steering Box to your frame. The kit is also useful for my application though since it comes with frame sleeves and a new mount that will make relocating the steering box much easier. Fabbed same thickness of toyota ifs box plate into the sector shaft are installed.

Chevy W 92-04 Ford BallJoint Dana 60. 1979-1995 Toyota Pickup Steering Stabilizer Kit. This frame mount kit includes both inner and outer frame reinforcing plates grade 8 bolts DOM tubing and Crimp nuts.

IFS box – CounterClockWise. Fits IFS box 86-95 on either a solid axle 79-85 truck 4 runner or factory IFS truck. I cut it long enough to run the steering box bolts through the part of the gusset against the frame and cut the back at a curve to avoid a perpenducular line of weld against the frame.

Chevy Dana 60 Kingpin Steering. 1979-1995 Toyota Pickup Steering Stabilizer Mount Kit. 92-20 Ford Balljoint 60 Steering.

Angled leading and trailing edges prevent frame cracking. Drilling the holes for the frame sleeves. Pre 79 Ford Dana 44 Steering.

Place steering box on frame rail and slide forward until it contacts body mount. 4 Remove top 4 bolts above sector shaft 14 mm. Install pitman arm onto steering box and snug down the sector shaft nut.

916-18 JIC -6 to M16-15 Adapter for IFS Steering Box. This kit is typically used by owners of 85 and older solid axle pickups when converting to crossover steering and the required IFS steering box. The IFS steering boxes are better suited to high steer than the push-pull boxes on 79-85 Toyotas because the pitman arm swings side-to-side instead of front-to-back.

Take the box mount it between the upright fender support and the old box mounting bracket. Chevy Axle. If youre installing crossover steering on your 79-85 4wd Toyota youre going to need to mount an IFS steering box.

6 Turn input shaft so internal piston moves toward input end. IFS Steering Box Mount. Add to Wish List.

Both inner and outer frame reinforcing plates made of 14 steel and steel DOM frame tubes to prevent frame-crumpling. Inner plate is 14 outer plate is 316. Fitting 14 Pipe to 6 JIC.

Low Pressure Return Fitting for 86-95 Toyota Pickup4Runner IFS Steering B. Ford Axle. Inner plate is 14 outer plate is 316.

My understanding that the FJ-80 box is also identical to the FJ556062 STEPS. Rotate the steering box. Toyota steering box mount instructions for this item is.

0 Remove and thoroughly clean outside of the steering box. No questions asked lifetime warranty. Includes grade 8 12 hardware may require reaming steering box bolts holes slightly.

Trail Gear Ifs Mount Install Help Yotatech Forums